K-1 Belay Pulley

The K-1 Belay Pulley can be used for both rope and cableÂ-equally at home on a belay cable or a Flying Squirrel! Designed for 3/8" wire rope or up to 1/2" belay rope. On traversing belays, connect the K-1 Belay Pulley to the Klinesaver using a 12 or 14mm rapid link.

• Durable, low friction bronze bearing
• Contoured edges for easier connection to belay cables and to prevent rope chafe
• Tensile tested to over 14,000 lb. (ACCT minimum standard is 5,000 lb)

J71143 $90.00

Klinesaver Shear Reduction Device

The Klinesaver shear reduction device is designed to significantly extend the usable life of belay rope, causing no appreciable loss of strength and durability due to rope shear.

• Large rope guide and curved entry helps prevent rope snags when loading belay rope.
• Designed to fit single 12 or 14mm rapid links for connection to a K-1 Belay Pulley on traversing elements or direct attachment to the belay cable on stationary elements.
• Tensile tested to over 12,000 lb. (ACCT minimum standard is 5,000 lb)
• Sheave is sculpted from marine grade anodized aluminum

J71194 $105.00

Rescue Kit

A rescue kit is a critical tool in the emergency action plan for your challenge course. A proper kit should always be on hand and ready for immediate deployment. We have assembled a pack of versatile gear you would need to perform a proper rescue on an outdoor course. Inside the durable cordura bag are: 120' of 7/16" orange KMIII Max static line, 5 Omega steel screwgate carabiners, 1 Clog Standard Figure 8 descender, 1 HB Sheriff belay device, 3 tied Technora Prusik slings, 1 pair utility scissors with sheath, 1 pair of basic belay gloves, 1 SAFER Lanyard with 2 snaps. Black KMIII is available on request.

J74033 $500

K-2 Zip Pulley

The K-2 Zip Pulley is simple in design and unrivaled in performance. Available in two sizes for use on both 3/8" and 1/2" diameter wire rope.

• Contoured edges provide easy connection to your Zip Wire
• The two hardened stainless steel sheaves with low friction sealed ball bearings make the pulley track like it's riding on rails.
• The elliptical clip-in hole provides enough space to comfortably handle two standard carabiners.
• Tensile tested to over 14,000 lb. (ACCT minimum standard is 5,000 lb)

S.A.F.E.R. (Shock Absorbing Fall Energy Regulator) Lanyard

To meet the challenge of evolving fall arrest standards in the Association for Challenge Course Technology (ACCT), PA replaced traditional Lobster Claws with our own ANSI/OSHA compliant energy-absorbing device. ACCT standards specify a maximum fall impact force to no more than 900 lb and the free fall distance to no more than 6'. Shock absorber activates at 450 lb. This year we offer an improved SAFER Lanyard with a forged steel D ring as an intermediate connection point and more flexible tails of 9,000 lb Type 18 webbing. Standard version comes with two sewn-in locking steel snaps. Also available without sewn-in snaps (so you can use auto locking carabiners) Designed for climbers up to 300 lb.

Challenge Course Sign

A good sign can help to discourage unauthorized use. This sign is durable and weather-resistant for good longevity. When attaching signs to trees, use galvanized roofing nails; when attaching to cinder blocks or concrete, use concrete nails or hot glue. Measures 9"x12"

J71122 $10.50

LEAP Anchor

The LEAP (Leading Edge Anchor Point) Anchor is a new solution to the problem of high-strength anchor points on challenge courses. PA's engineers have produced a high-strength, multi-purpose anchor that can be used equally well as self-belay anchors on staple climbs or as the ideal termination fitting on belay cables anywhere where the cable load is at 90° to the angle of the bolt.

Features of the LEAP Anchor:

• Designed for use with 5/8" x 6" Lag Screws or 5/8" machine bolts and 5/8" Round Washers. (sold separately-SEE BELOW)
• Tested to over 9,500 lb without anchor failure
• Exceeds ACCT's "Standard Anchor" strength of 5,000 lb (even in soft white pine trees, test results averaged over 7,000 lb when using 5/8" x 6" lag screws). ACCT's "Leading Edge" anchor standard is 2,500 lb.
• Double coated for corrosion resistance Â- zinc plated and powder-coated
• Available in bright orange or gray

LEAP Anchor Lag Screw Galvanized

5/8 Nut Eye Bolt

A strong and dependable through-bolt anchor for belay or element connections.

5/8 Machine Bolt

A widely-used structural bolt to secure beams to trees or poles.

1/2 Lag Screw

Hex-headed screw used for attaching sections of lumber (platforms, horizontal wall or tower supports) to trees or utility poles.

Oversized 5/8

The best all-around washer for 5/8" bolts. They don't need to be "squared-up" for professional appearance and they are more substantial than standard round washers. Size: 2 1/4" diameter, galvanized.

J71279 $1.05

Round Washer

Galvanized, for 1/2" and 5/8" screws and bolts.

Curved Square Washer

Curved to match the shape of a utility pole. Size: 2 1/4"x 21/4", galvanized.

J71275 $1.00

Fish Plate

Galvinized washer used primarily on softwood trees. Size: 2 1/4" x 2 1/4".

J71281 $0.70

Tuna Plate

Helps spread the load in walls and beams indoors. Size: 4"x4", galvanized.

J71282 $2.35

Two Coil Lock Washer

Used to ensure the tightness of a nut when installed on utility poles, lumber or buildings. For 5/8" bolts, galvanized.

J71274 $0.55

Standard Wire Rope

Good quality imported wire rope for the budget-sensitive. 5/16" and 3/8" diameter.

Wire Rope Clips

Domestically made, wire rope clips make a secure end connection on wire rope. Not to be confused with the less expensive 'malleable' type of clip which are not acceptable for use on challenge courses.

Crosby Fist Clips

The best adjustable wire rope termination, providing good holding power without deforming the cable. 3/8" size only.

J71064 $7.70

Serving Sleeve

Provides a safe and professional covering for ends of clamped wire rope connections. Order 3/8" serving sleeves for 5/16" wire rope and 7/16" serving sleeves for 3/8" wire rope.

Oval Sleeves (Ferrules)

Made of zinc plated copper, swaged connections are the highest strength termination on wire rope — professional and permanent. They require a swage tool to properly crimp.

Wire Rope Thimble

Choose this heavy gauge thimble for cable connections to Nut Eye Bolts — it slips easily onto the bolt eye. 3/8" size for 3/8" wire rope.

J71264 $0.95

Maillon Rapide (Rapid) Links

Commonly called rapid links, these strong connectors are widely used on challenge courses. For the highest quality we use only authentic Maillon Rapide links. The hexagonal sleeve can be tightened down with a wrench to combat vandalism. The 12mm size is also available in stainless steel for joining the K-2 Belay Pulley and the Klinesaver.

Size/Safe Working Load: 10mm (7/16") 1000 kg, 12mm (1/2") 1500 kg, 14mm (9/16") 2200 kg, 16mm (5/8") 2900 kg

Aluminum Snap Links

These small carabiners are handy for low load applications such as indoor haul systems and SpiderÂ’s Web connections. Do not use for belays or other critical applications.

J71007 $2.00

Staples

1/2" staples are commonly used to create access climbs on trees and utility poles. For most trees and all utility poles, pre-drilling a 3/8" hole to the proper depth creates a stronger and better placement. 1/2" staples are available in 6" and 8" lengths. For greater holding power, use 8" staples on softwood trees. 3/8" staples are useful as light attachments for a Spider's Web or Maze.

Turnbuckles

Used for put-up/take-down systems–easy to adjust cable tension or completely remove foot cables. 5/8" x 12" (closed length). Hook/eye, hook/hook styles.